washing machine service center in bangalore

If the machine door does not open after the wash cycle (given that you waited 5 minutes), then most likely there are problems with the locking system. It is necessary to turn off the power from the network and wait 15 minutes, during which time the hatch locking device will reboot. Sometimes turning on the spin mode again helps, after which the hatch opens again.

In this case, you should immediately seek qualified help. The problem may be related to:

• With device closure,
• With hard water
• With voltage drops,
• With long-term use.

A specialist will be able to find out the true cause of the malfunction and eliminate it as quickly as possible.

When the spinning function stops working, it is also preferable to seek help from a specialist.

The problem may be related to:

• With heating element,
• With a malfunction of the electric motor or wear of its brush,
• With damage to the “Off mode” switch.

Another malfunction is noise during the spin cycle. The spinning sounds can be similar to a jet plane. If you hear such sounds, you should stop washing. Broken bearings can make noise. Bearings rust from water and break after 5 years of service.

• One of the most common cycle problems is when the water heater or its control system fails and the hot wash cycle is skipped.
• Another serious problem is the failure of the control module. The reason is a violation of the machine’s operating algorithm: continuous washing, unexpected stops.
• In some cases, the machine drains water while rinsing. The cause may be damage to the self-cleaning pump. Such a part cannot be repaired if there is a mechanical defect, and the average service life of such a pump is 5 years.

If this type of breakdown occurs, you should immediately call a specialist.

During the washing process, the washing machine may stop and not drain the water. The reason is a clogged pump, drain filter or hose. You can check and clean the filter and hose yourself. If the problem persists, most likely the pump has failed - contact our specialist for help.

The most common cause is a leak in the door gasket and at the hose connection.

Water leaks generally occur when:

• The machine is not installed correctly,
• There are damages or cracks in the hoses,
• The new device has a manufacturing defect.

You can fix these three problems yourself. It is enough to reinstall the device, change the hoses, or call a service center employee for diagnostics and further resolution of the issue.

However, experts identify three more reasons why water may leak in washing machines:

• The water supply pressure is too intense,
• The dispenser is filled with powder beyond the norm, which prevents water from draining into the tank, as a result of which leakage occurs,
• The dispenser is filled with dried detergent residue.

Make sure the machine is on a level surface. If the floor is ideal, then installing special anti-vibration pads will help. If everything is fine with this, but the problem remains, it is time to call a specialist.

Problems with the drum occur when the washing machine is regularly overloaded.

This may also cause:

• Loose or damaged drive belt,
• Getting a foreign object between the drum and the tank,
• Failure of the electronic module,
• The hatch door lock is broken,
• Damage to the entire engine.

In any case, detailed diagnostics and qualified repairs will be required. There is no need to try to fix the problem yourself, as you can only cause harm and completely disrupt the working settings of the sensors.

In most cases, this is due to belt wear. You won’t be able to eliminate the noise on your own; it’s better to call our technician who will quickly replace the belt.

This case is by no means considered critical. A clogged filter is the most common cause of this problem. You can clean the filter yourself and see the results.

Before calling a specialist, make sure that:

• There is no debris in the filter,
• The system is at normal pressure,
• The valve is open,
• The washing machine door is closed.

If the problem persists, call us and we will fix everything. Most likely, the electronic module, relay or fill valve has broken down.

The most common cause of bad odors in your washing machine is bacteria or mold living and growing inside. To solve the problem, some recommend running a wash cycle with a mixture of vinegar and baking soda, this solution will eliminate any mold and bacteria.